Xhorse Remote Tester Work on 868Mhz Frequency, Possible?

In general, Xhorse Remote Tester only has 2 frequency test range: 300Mhz-320Mhz & 434Mhz. Is it possible to change the Xhorse tester to work on 868Mhz? It actually can. Follow the tip below to learn how to do.


How to change Xhorse tester to work on 868Mhz?

1. Remove battery from remote tester.

change-xhorse-remote-tester-work-on-868mhz-frequency-1

2. Unscrew the 4 screws on backside of tester.

change-xhorse-remote-tester-work-on-868mhz-frequency-2


3. Open back cover, find the jumper cap position on device board. Change the jumper cap from left 2 pins to right 2 pins.

change-xhorse-remote-tester-work-on-868mhz-frequency-3

change-xhorse-remote-tester-work-on-868mhz-frequency-4


4. Assemble remote tester to have a try.

change-xhorse-remote-tester-work-on-868mhz-frequency-5

The Xhorse Frequency Tester can now detect 868MHz frequency.

Very easy and done.

Hope this is helpful.


Technical support

www.xhorse.co.uk



Comments

Post a Comment

Popular posts from this blog

Xhorse VVDI Prog V5.3.0 Update and Software Download

Xhorse VVDI Prog can be upgraded to the 5.3.0 version now, this post will give you the software download link and more details. Download Free: https://we.tl/t-33MIuwcvaF Password: 123456 * This version DON't need updated firmware * Modify GL8 BCM(2017--)-WRITE, option in <4-IMMOBILIZER>-><BUICK>: Optimize the process +Add FENGSHEN S30(93C46A) option in <8-OTHER>-><Dongfeng> www.xhorse.co.uk
Read more

Xhorse MVCI PRO J2534 Driver Free Download & User Guide

Image
Xhorse.co.uk provides Xhorse MVCI PRO J2534 Driver free download & installation user guide. Compatible with VAG ODIS, TIS(Toyota Techstream), Honda HDS, Subaru SSM4, FDRS IDS, and Mazda IDS diagnostic software. Where to free download Xhorse MVCI Pro j2534 driver? https://mega.nz/file/MuoiBJZa#MjmQNzgll4pJEERnq1v__sHx6n3C9nr-cMwJqChNPAs Software Size: 52.2MB Language: English, Chinese Operating System: Windows7, Windows10 How to install & start Xhorse MVCI PRO J2534? *Note: Ensure your computer has the original diagnostic software supporting J2534. Please download it from the original manufacturer's website or a third party. 1. Install the J2534 driver Select language >> Next >> Next >> Install >> Finish 2. Connect MVCI PRO J2534 to car OBD & computer. 3. Start MVCI PRO J2534. ① Click "Connect": after a successful connection, here can check the device info including firmware version, serial number, etc. ② Read authorization - read the ...
Read more

Xhorse VVDI Key Tool Plus Read & Unlock VW MQB48 NEC35xx

Image
This is a tutorial on how to read & unlock Volkswagen MQB48 NEC35xx immo data with Xhorse VVDI Key Tool Plus . Needs to activate VAG MQB License & disassemble instrument from vehicle. You'll also need to lift the pin from PCB or cut pin connections while reading data(*See the guidance at the end of this article) 1.Read MQB IMMO Data Immo programming >> VW >> Select by type >> MQB instrument immo system >> Instrument - MQB48(VDO/JCI- NEC35xx locked) >> Start programming Disclaimer: When using this function to read data, you need to Lift the PIN from PCB or Cut PIN Connections. Please operate carefully, wire accurately, and pay attention to the protective dashboard. It is recommended to learn how to Lift the PIN from PCB and Cut PIN connections by yourself.  Press "OK". This function needs to be connected to the network, please make sure that network connection is normal. Press "OK". Read IMMO data >> Use the programmer...
Read more